BRUSHLESS ESC’s

AIRPLANE, HELICOPTER AND CAR/TRUCK ESC's

QUICK LINK TO:

HIGH VOLTAGE ESC

BRUSHLESS MOTOR

MICRO BRUSHLESS MOTORS

UBEC

DUCTED FANS

3A VOLO Brushless Speed Controller ESC

IN STOCK

less Speed Controller ESC

Amps	3A / 4A max
Weight	1g
Price	$20

THESE LITTLE BEAUTIES ARE MADE FOR 3A CONTINUOUS DRAW, FOR 2 GRAM AND 5 GRAM BRUSHLESS MOTORS. THEY ARE LIMITED TO 4.2V MAX (SINGLE LIPO CELL)

1. Continuous current: 3A
2. Burst current: 4A
3. Cell of Li-XX: 1
4. Max voltage: 4.2V
5. Weight: 1g
6. Dimension(mm): 11x13x8

THE MICRO RX IS POWERED DIRECTLY BY THE LIPO CELL

RECOMMENDED MOTOR:

2g 7700kv

5g 3700kv

Scroll down to see motors

70mAh cells are available in the Loose cells section.

7A VOLO Brushless Speed Controller ESC

less Speed Controller ESC

Amps	7A / 9A max
Weight	5.4g
Price	$24

FULLY PROGRAMMABLE WITH THROTTLE STICK OR OPTIONAL VOLO PASS PROGRAM CARD

7A Brushless Electronic Speed Controller

Can be made under 5g if you remove shrink and most of wires. Very good controller for Mini and Micro applications
BEC: 1A /5V
Size: 22x12x5 mm
Input voltage: 3V -9V

12A VOLO Brushless Speed Controller ESC

less Speed Controller ESC

VOLO 12A ESC Brushless Speed Controller for Airplane or Helicopter

Amps	12A / 15A max
Weight	5.4g
Price	$26

FULLY PROGRAMMABLE WITH THROTTLE STICK OR OPTIONAL VOLO PASS PROGRAM CARD

12A Brushless Electronic Speed Controller for 1-3S lipo

BEC: 1A/5V
Size: 22x17x7 mm
Input voltage: 3V -13V

VOLO XP 18A Brushless Speed Controller ESC

VOLO 18A Brushless ESC

Amps	18A / 22A max
Weight	19g
Price	$ 22

18A Brushless Electronic Speed Controller

Constant Current 18A

Max Current 22A (10sec)

2S-4S LIPO WITH BEC

ONE OF THE BEST AND ORIGINAL ESC TO COME OUT OF CHINA.

USE WITH PARK 300-400 motor

Built in 2A/5V BEC

3S - 5 servo
4S - 4 Servo

YOU CAN:
CHANGE THROTTLE CURVE,
PROGRAM TIMING
GOVERNOR
BRAKE
START (FAST, SOFT, V.SOFT)
CUT-OFF TYPE
LVC
PWM
START POWER

STORM 18A Brushless Speed Controller ESC

FULLY PROGRAMMABLE

ushless Speed Controller ESC

FULLY PROGRAMMABLE

Programs with throttle stick or with optional Storm Link

Amps	18A / 20A max
Weight	18g
Price	$ 30

* High rate (10 KHz) switching (PWM)
* Six to twelve NiCd, Ni-MH cells or two to four Li-poly cells with receiver.
* Up to ten NiCd, Ni-MH cells or three Li-poly cells with three micro servos.
* Twelve NiCd, Ni-MH or four Li-poly cells MAX (with BEC disabled).
* Powerful direct-drive ability (High-torque drive ability).
* Smooth Linearity of throttle.
* Dynamic braking ensures prompt prop folding.
* BEC (2.0A) provides power to receiver and servos -eliminates separate receiver battery.
* Over temperature protection.
* User Programmable Features.
* Low-voltage protection - the value of low-voltage cutoff can be set at 4.8V, 5.6V, 6V, 7.2V, 8.4V, 9V, 11.2V and 12V.
* Cutoff can be programmed for motor stop or reduced power.
* Brake Type selectable.
* Throttle Range.
* Timing Advance: 4 to 10 degree, 10 to 20 degree, 20 to 30 degree to suite different magnet poles motors.
* Safe "power on" arming program ensures motor will not accidentally turn on.
* Low torque "soft start" prevents damage to fragile gearboxes.
* Lost single protection: Auto shut down in 4 sec after signal is lost or radio interference becomes severe.
* Microprocessor controlled.
* Optional PC connection and set up via PC LINK, you can even test your power system via PC software designed for the ESC.
* Change the rotation by programming
* Motor Jam Protect: When motor jam normally make the ESC overheat, powerful hardware and software design will protect the ESC from damage.
* Over heat protection: ESC will cut-off when temperature is higher than 155 degree.
* Over voltage protection: ESC will cut-off when input voltage is higher than 18V.

VOLO XP 25A Brushless Speed Controller ESC

VOLO 25A Brushless ESC

ACTUAL COLOR IS BLUE WIRE YELLOW SHRINK

JUST LIKE VOLO 18A ABOVE

Amps	25A / 35A max
Weight	22g
Price	$ 26

25A Brushless Electronic Speed Controller

Constant Current 25A

Max Current 35A (10sec)

2S-4S LIPO WITH BEC

ONE OF THE BEST AND ORIGINAL ESC TO COME OUT OF CHINA.

USE WITH PARK 400-480 motor
PERFECT FOR SMALL HELICOPTERS AND PLANES

Built in 2A/5V BEC

3S - 5 servo
4S - 4 Servo

YOU CAN:
CHANGE THROTTLE CURVE,
PROGRAM TIMING
GOVERNOR
BRAKE
START (FAST, SOFT, V.SOFT)
CUT-OFF TYPE
LVC
PWM
START POWER

STORM 25A Brushless Speed Controller ESC

FULLY PROGRAMMABLE

Programs with throttle stick or with optional Storm Link

Shown back & front

Amps	25A / 35A max
Weight	18g
Price	$ 40

STORM 35A Brushless Speed Controller ESC

FULLY PROGRAMMABLE

Programs with throttle stick or with optional Storm Link

Amps	35A / 45A max
Weight	22g
Price	$ 45 SALE

THIS ESC WORKS VERY WELL ON HIGH SPEED WINGS WITH 450 SIZE OUTRUNNER AND 2S-3S LIPO

HOBBY-40A Brushless Speed Controller ESC

ONLY 1 LEFT

Programs with JETI Program Card

FOR HELICOPTER OR AIRPLANE

Amps	40A / 50A max
Weight	36g
Price	$ 40

2S-4S LIPO WITH BEC

NICE AND INEXPENSIVE CONTROLLER. PROGRAMS WITH JETI CARD

USE IN ANY 15-46 size conversion

VOLO-40A Brushless Speed Controller ESC

Programs with throttle stick or Program Card

FOR HELICOPTER OR AIRPLANE

Amps	40A / 50A max
Weight	38g
Price	$ 60

2S-5S LIPO WITH BEC

ONE OF THE BEST AND ORIGINAL ESC TO COME OUT OF CHINA.

USE IN ANY 15-46 size conversion

Built in 3A/5V BEC

3S - 5 servo
4S - 4 Servo
5S - 3 servo

FOR MORE SERVOS ON 5S USE RX BATTERY

YOU CAN:
CHANGE THROTTLE CURVE,
PROGRAM TIMING
GOVERNOR
BRAKE
START (FAST, SOFT, V.SOFT)
CUT-OFF TYPE
LVC
PWM
START POWER
MOTOR ROTATION

STORM 60A Brushless Speed Controller ESC

FULLY PROGRAMMABLE

UP TO 6 CELL LIPO

WITH UBEC OR RX PACK

Programs with throttle stick or with optional Storm Link

Amps	60A / 80A max
Weight	44g 1.6oz
Price	$70 SALE

* High rate (10 KHz) switching (PWM)
* 6 to 12 NiCd, Ni-MH cells or 2-3 Li-poly cells with receiver.
* Up to 10 NiCd, Ni-MH cells or 3 Li-poly cells with three micro servos.
* 18 NiCd, Ni-MH or 6 Li-poly cells MAX (with BEC disabled).
* Powerful direct-drive ability (High-torque drive ability).
* Smooth Linearity of throttle.
* Dynamic braking ensures prompt prop folding.
* BEC (2.0A) provides power to receiver and servos -eliminates separate receiver battery.
* Over temperature protection.
* User Programmable Features.
* Low-voltage protection - the value of low-voltage cutoff can be set at 4.8V, 5.6V, 6V, 7.2V, 8.4V, 9V, 11.2V and 12V.
* Cutoff can be programmed for motor stop or reduced power.
* Brake Type selectable.
* Throttle Range.
* Timing Advance: 4 to 10 degree, 10 to 20 degree, 20 to 30 degree to suite different magnet poles motors.
* Safe “power on” arming program ensures motor will not accidentally turn on.
* Low torque “soft start” prevents damage to fragile gearboxes.
* Lost single protection: Auto shut down in 4 sec after signal is lost or radio interference becomes severe.
* Microprocessor controlled.
* Optional PC connection and set up via PC LINK, you can even test your power system via PC software designed for the ESC.
* Change the rotation by programming
* Motor Jam Protect: When motor jam normally makes the ESC overheat, powerful hardware and software design will protect the ESC from damage.
* Over heat protection: ESC will cut-off when temperature is higher than 155 degree.

VOLO-60A Brushless Speed Controller ESC

Programs with throttle stick or Program Card

FOR HELICOPTER OR AIRPLANE

Amps	60A / 80A max
Weight	45g
Price	$ 80

2S-5S LIPO WITH BEC
UP TO 6S WITHOUT BEC

ONE OF THE BEST AND ORIGINAL ESC TO COME OUT OF CHINA.

I USE THIS WITH MY "PLASTIC CONCEPT PLANES" TALON WITH 3520-7 MOTOR AND 11x5.5 PROP ON A 5S 4000mAh 10C LIPO
THIS SETUP WILL MOVE 5LB PLANE VERY EFFICIEINTLY

Built in 3A/5V BEC

3S - 5 servo
4S - 4 Servo
5S - 3 servo
6S - as many as your RX battery can support

YOU CAN:
CHANGE THROTTLE CURVE,
PROGRAM TIMING
GOVERNOR
BRAKE
START (FAST, SOFT, V.SOFT)
CUT-OFF TYPE
LVC
PWM
START POWER
MOTOR ROTATION

VOLO-80A Brushless Speed Controller ESC

Programs with throttle stick or Program Card

FOR HELICOPTER OR AIRPLANE

Amps	80A / 100A max
Weight	60g
Price	$ 100

2S-5S LIPO WITH BEC
UP TO 6S WITHOUT BEC

ONE OF THE BEST AND ORIGINAL ESC TO COME OUT OF CHINA.

Built in 3A/5V BEC

3S - 5 servo
4S - 4 Servo
5S - 3 servo
6S - as many as your battery can support

YOU CAN:
CHANGE THROTTLE CURVE,
PROGRAM TIMING
GOVERNOR
BRAKE
START (FAST, SOFT, V.SOFT)
CUT-OFF TYPE
LVC
PWM
START POWER
MOTOR ROTATION

VOLO-HV80A Brushless Speed Controller ESC

Programs with throttle stick or Program Card

FOR HELICOPTER OR AIRPLANE

Amps	80A / 100A max
Weight	150g
Price	$ 120

3S-10S LIPO

ONE OF THE BEST AND ORIGINAL ESC TO COME OUT OF CHINA.

10AWG WIRE

YOU CAN:
CHANGE THROTTLE CURVE,
PROGRAM TIMING
BRAKE
START (FAST, SOFT, V.SOFT)
CUT-OFF TYPE
LVC
PWM
START POWER
MOTOR ROTATION

STORM 120A Brushless Speed Controller ESC

FULLY PROGRAMMABLE

UP TO 6 CELL LIPO

WITH UBEC OR RX PACK

Programs with throttle stick or with optional Storm Link

Amps	120A / 140A max
Weight	55g 1.9oz
Price	$110

* High rate (10 KHz) switching (PWM)
* 6 to 18 NiCd, Ni-MH cells or 2-6 Li-poly cells with receiver.
* Up to 10 NiCd, Ni-MH cells or 6 Li-poly cells with three servos.
* 18 NiCd, Ni-MH or 6 Li-poly cells MAX (with BEC disabled).
* Powerful direct-drive ability (High-torque drive ability).
* Smooth Linearity of throttle.
* Dynamic braking ensures prompt prop folding.
* BEC (2.0A) provides power to receiver and servos -eliminates separate receiver battery.
* Over temperature protection.
* User Programmable Features.
* Low-voltage protection - the value of low-voltage cutoff can be set at 4.8V, 5.6V, 6V, 7.2V, 8.4V, 9V, 11.2V and 12V.
* Cutoff can be programmed for motor stop or reduced power.
* Brake Type selectable.
* Throttle Range.
* Timing Advance: 4 to 10 degree, 10 to 20 degree, 20 to 30 degree to suite different magnet poles motors.
* Safe “power on” arming program ensures motor will not accidentally turn on.
* Low torque “soft start” prevents damage to fragile gearboxes.
* Lost single protection: Auto shut down in 4 sec after signal is lost or radio interference becomes severe.
* Microprocessor controlled.
* Optional PC connection and set up via PC LINK, you can even test your power system via PC software designed for the ESC.
* Change the rotation by programming
* Motor Jam Protect: When motor jam normally makes the ESC overheat, powerful hardware and software design will protect the ESC from damage.
* Over heat protection: ESC will cut-off when temperature is higher than 155 degree.

VOLO-HV120A Brushless Speed Controller ESC

Programs with throttle stick or Program Card

FOR HELICOPTER OR AIRPLANE

Amps	120A / 150A max
Weight	180g
Price	$ 160

VOLO PASS - ESC PROGRAM CARD

PROGRAM CARD FOR

VOLO AIR AND CAR ESC

Volo Pass - program card for Volo ESC TrueRC

Price

$ 20

Programs following features on Volo ESC's:

VOLTAGE CUT OFF (LVC)
BRAKE TYPE
TIMING
START TYPE
CUT OFF TYPE
FREQ. (PWM)
THROTTLE RANGE
THROTTLE CURVE
GOVENROR
START POWER
MODEL (CAR PLANE/HELI)
MOTOR DIRECTION
CAR THROTTLE TYPE (3 TYPES)

STORM LINK CABLE & SOFTWARE

Price SERIAL

$ 9

Price

USB

$ 15

Very simple to set up

Current software allows programming LVC at increments of 0.01V

For use with Li-Polymer, NiCd and NiMH

FIVE PROGRAMMABLE SETTINGS

1. CUTOFF VOLTAGE (8 settings)

2. BRAKE (ON /OFF)

3. TIMING ADVANCE (3 settings)

4. CUTOFF TYPE (SOFT / HARD)

5. ROTATION (FORWARD / REVERSE)

ALSO RUN BENCH OR FIELD TESTS ON YOUR LAPTOP OR PC

ALLOWS YOU TO SET NUMBER OF MAGNET POLES OF YOUR MOTOR AND ACURETLY TIME YOUR MOTOR. ALSO SHOWS RPM. RUN WITH OR WITH OUT A PROP

3A Ultra BEC Board

ALSO PERFECT FOR

GAS FLYING MODELS WITH USE OF LI-POLY RX PACKS

Amps	3A
Weight	12g
Price	$12 SOLD OUT

The UBEC Board is specially designed for 50A & 60A Brushless ESC's and & Dynam 45A, 60A and 70A Brushless ESC's to support more servos without using a separate RX battery to power servos.

PERFECT FOR 60A, HV80A HV110A and 120A STORM ESC's

Size: 2.57*1.3*1.0cm
Max Input V: 35V (8 cells Lipo or 24 Cell Ni-Mh cells)
Output V: 5V/6V (Jumper out: 6V Jumper in: 5V)
Output Current: Consistent 3A
Max: 5A (Less than 3 seconds)
PWM: 250KHZ
Max efficiency: 86%

Numbers of servos supported:

	5V	6V
STD SERVO	10pcs	8pcs
HIGH TORQUE SERVO	5pcs	4pcs
DIGITAL SERVO	4pcs	3pcs

3A ASSAN Ultra BEC Board

ALSO PERFECT FOR

GAS FLYING MODELS WITH USE OF LI-POLY RX PACKS

Amps	3A /5A max
Weight	15g
Price	$10

The ASSAN UBEC Board is specially designed for 50A & 60A Brushless ESC's and & Dynam 45A, 60A and 70A Brushless ESC's to support more servos without using a separate RX battery to power servos.

PERFECT FOR HV45A, 60A, 80A, HV80A HV110A and 120A STORM ESC's

Board Size:38mm x 21mm x 10mm
Max Input V: 23V ( 5 cells Lipo or 19 Cell Ni-Mh or NiCD cells)
Output V: 5V/6V (selected with Jumper)
Output Current: Constant 3A
Max: 5A ( Less than 3 seconds)

Connectors:

INPUT: N/A

OUTPUT: BLACK J-type

Numbers of servos supported:

	5V	6V
STD SERVO	10pcs	8pcs
HIGH TORQUE SERVO	5pcs	4pcs
DIGITAL SERVO	4pcs	3pcs

3A ASSAN EXTRA BEC with LIPO ALARM

EXTRA BEC WITH LIPO WARNING

ALSO PERFECT FOR

GAS FLYING MODELS WITH USE OF LI-POLY RX PACKS

Amps	3A /5A max
Weight	20g
Price	$22

The ASSAN EXTRA BEC Board is specially designed for 40-120A Brushless ESC's

to support more servos when using a 2S lipo battery as your RX pack.

PERFECT FOR HV45A, VOLO 60A,

VOLO 80A, HV80A HV120A and 120A STORM ESC's

Max Input V: 8.4V ( 2 cells Lipo)
Output V: 5V/6V (selected with Jumper)
Output Current: Constant 3A
Max: 5A ( Less than 3 seconds)

LIPO ALARM: at 6.6V

Connectors:

INPUT: JST

OUTPUT: BLACK J-type

Numbers of servos supported:

	5V	6V
STD SERVO	10pcs	8pcs
HIGH TORQUE SERVO	5pcs	4pcs
DIGITAL SERVO	4pcs	3pcs

BRUSHLESS MOTORS

CR28M CONTRA ROTATING BRUSHLESS MOTOR WITH PROPS

CONTRA ROTATING CR-28M MOTORS

KV	1050
Weight	79g
Price	$ 135

Dimension：Φ28mm x 51mm

Weight：79g / 2.83oz (not including connectors)

Diameter of shaft：Φ3.0mm

Length of front shaft：10.25mm

Props L/R 10x4

11V @ 10.5A x 2 Thrust:1320g/46.56oz

USE 15-25A ESC's

PERFECT MOTOR TO GET THE SCALE LOOK ON THE ANTONOV AN-22, BUGATTI MODEL 100, P-51Unlimited Racer, or The Martin-Baker M.B.5 and the XB-35

2 GRAM MICRO Brushless Outrunner Motor

NOW IN STOCK

2g brushless outrunner , 2 gram micro motor

KV	7700
Weight	2g
Price	$ 15

The D1000 is a micro 2g brushless outrunner designed purely for indoor Single cell (4.2V max) li-poly use.
Combined with our micro 3A ESC, its a perfect combination for micro indoor EP planes.

Kv:7700rpm/v
Weight: 2g
Voltage: 3.7v (4.2V max)
No Load Current: 0.1A
No Load Speed : 12200
Load Current: 1.5A
Suggested Propeller: GW/EP 3020

Thrust: 36g+
Shaft: 1mm

5 GRAM MICRO Brushless Outrunner Motor with Mount

6 IN STOCK

Propeller	Test Volts(V)	Test Current(A)	Thrust(g)	Thrust(oz)	Power(W)
GWS ep2510	7.4	0.8	38	1.34	5.92
GWS ep2510	8	0.9	43	1.52	7.2
GWS ep2510	8.4	1	49	1.73	8.4
GWS ep3020	7.4	2.5	84	2.97	18.5
GWS ep3020	8	2.8	90	3.18	22.4

KV	3700
Weight	5g
Price	$ 26

Kv: 3700
Cells: 1-2
Current: 2A
Prop:3x2 or 2.5x1
Pull: 90 g
Shaft Size:1.5 mm

motor weighs 4.6 grams without the mount

Firewall mount (and hardware) included as shown.

USE 3A ESC with single cell lipo or 6A ESC with 2S lipo, WE SUGGEST STRIPPING THE 6A ESC IT DOWN TO BARE BOARD FOR MICRO PLANE PROJECTS AND SOLDERING MOTOR DIRECT TO THE ESC'S PCB TO SAVE WEIGHT.

LOOKING FOR 30mm 9.5g DUCTED FAN ?

- KEEP SCROLLING DOWN

5 GRAM MICRO Brushless Outrunner Motor with Mount

5 IN STOCK

Walkera 4G3 Brushless motor conversion C05_11500v ADH50

PERRFECT FOR BRUSHLESS CONVERSION OF WALKERA 4G3 HELICOPTER

KV	11500
Weight	5g
Price	$ 28

Kv: 11500
Cells: 1
Current: TBA
Prop:TBA
Pull: TBA
Shaft Size:1.5 mm

motor weighs 4.6 grams without the mount

Firewall mount (and hardware) included as shown.

USE VOLO 3A ESC with single cell lipo

5 GRAM MICRO Brushless Outrunner Motor

KV	2000
Weight	5g
Price	$ 20

Kv: 2000
Cells: 2
Current: 2A
Prop:4x2.5
Pull: 90 g
Shat Size:1.5 mm

motor weighs 5 grams without the mount or the prop saver.

Prop saver and mount are included as shown.

USE 6A ESC WE HAVE FOR THIS MOTOR, I WOULD SUGGEST STRIPPING IT DOWN TO BARE BOARD FOR MICRO PLANE PROJECTS AND SOLDERING MOTOR DIRECT TO THE ESC'S PCB TO SAVE WEIGHT.

10 GRAM MICRO Brushless Outrunner Motor

stock photo

KV	2000
Weight	10g
Price	$ 21

Weight:10grams
KV:2000
Cells:2
Prop:7x5
Current: 4.5A
Speed:5500 RPM
Pull:140g
Max Current: 5.3A

GWS 6X3	3A	23 W	10200 RPM	28.98 MPH
GWS 7X3.5	3.7A	28 W	8600 RPM	28.5 MPH
GWS 6X5	4.0A	30 W	7750 RPM	36.7 MPH
APC 7X4	4.5A	32 W	6650 RPM	25.19 MPH

motor actually weighs 9.7 grams without the mount or the prop saver.

Prop saver, prop adapter and mount are included as shown.

USE 6A ESC WE HAVE FOR THIS MOTOR, I WOULD SUGGEST STRIPPING IT DOWN TO BARE BOARD FOR MICRO PLANE PROJECTS AND SOLDERING MOTOR DIRECT TO THE ESC'S PCB TO SAVE WEIGHT.

8.5 GRAM MICRO Brushless Outrunner Motor C10

ONLY FEW LEFT

high quality cnc motor only 8.5g

KV	2100
Weight	8.5g
Price	$ 20

Weight: 8.5 grams w/ wires and mount
(7.9 grams w/o mount)
Kv: 2100 RPM/V
Max Current: 5 Amps
Size: 17.8 mm diameter x 20 mm long
2mm Shaft
6 magnet poles
Includes removable firewall mount
Use with 5x4 prop and 2S lipo

USE 6A ESC WE HAVE FOR THIS MOTOR, I WOULD SUGGEST STRIPPING IT DOWN TO BARE BOARD FOR MICRO PLANE PROJECTS AND SOLDERING MOTOR DIRECT TO THE ESC'S PCB TO SAVE WEIGHT.

8.5 GRAM MICRO Brushless Outrunner Motor C10

TEMP OUT OF STOCK

high quality cnc motor only 8.5g

KV	2900
Weight	8.5g
Price	$ 20

Weight: 8.5 grams w/ wires and mount
(7.9 grams w/o mount)
Kv: 2900 RPM/V
Max Current: 5 Amps
Size: 17.8 mm diameter x 20 mm long
2mm Shaft
6 magnet poles
Includes removable firewall mount
USE WITH 4x3 prop and 2S lipo

USE 6A ESC WE HAVE FOR THIS MOTOR, I WOULD SUGGEST STRIPPING IT DOWN TO BARE BOARD FOR MICRO PLANE PROJECTS AND SOLDERING MOTOR DIRECT TO THE ESC'S PCB TO SAVE WEIGHT.

C20 PRO -1550 / 2050 MINI Brushless Outrunner Motor

high quality cnc motor
perfect for
MSComposit Mini Swift
2050 Works very well with our 10A ESC's
and 2S 900 pack on that wing. Very fast

KV	1550 / 2050
Weight	25.5g

Price	$ 22 1550kv
Price	$ 22 2050kv

Dimension：Φ23mm x 24mm

Weight：25.5g 0.89oz (kv1550 kv2050)

Diameter of shaft：3mm

Length of front shaft：8mm

KV：1550 / 2050 /

MOTOR	Propeller:	Volts:	Amps:	Thrust:
1550	GWS 8 x 4	7.0 V	6.1 A	285 g / 10 oz
1550	GWS 8 x 4	8.0 V	7.5 A	356 g / 12.56 oz

Max Current: 9 Amps

MOTOR	Propeller:	Volts:	Amps:	Thrust:
2050	GWS 7 x 3.5	8.0 V	8.1 A	340 g / 11.99 oz
2050	GWS 7 x 3.5	11.0 V	12.8 A	558 g / 19.68 oz

Max Current: 13.5 Amps

USE 10A-12A ESC FOR THIS MOTOR

Brushless Outrunner CDROM Motor

Great for small wings and park flyers with 7x5 to 8x4 prop

KV	1300
Weight	25g as shown
Price	$ 20

Working Current 6-8A
Peak Current 11A (110W bursts)
Shaft size: 3mm diameter x 42mm long
Motor Size: 27mm diameter, 30mm long
Pre installed 2mm connector ( female also included)
Recomended ESC: 10A
Recomended prop: 7x6 or 8x4
Stator Size: 22mm
Turns: 14
AWG: 26

Recommended for planes with 2S and 3S battery up to 12oz

Load with 8x4 prop: 9A @ 5580RPM

Brushless Outrunner CDROM Motor

Great for small 3D and park flyers with 9x4 prop

KV	1000
Weight	25g as shown
Price	$ 20

Working Current 6-8A
Peak Current 11A (110W bursts)
Shaft size: 3mm diameter x 42mm long
Motor Size: 27mm diameter, 30mm long
Pre installed 2mm connector ( female also included)
Recomended ESC: 10A
Recomended prop: 7x6 or 8x4
Stator size: 22mm
Turns: 17
AWG: 26

Recommended for all planes with 3S battery up to 12oz

Perfect for 3D IKARUS Shockflyer

Hyper Speed Brushless Outrunner CDROM Motor

CAN BE MOUNTED ON STICK WITH OPTIONAL STICK MOUNT

This is a high speed motor.

good to power small wings wit 3S packs or lite models with 2S packs and 7x5 prop

KV	2100
Weight	23g
Price	$ 20

Working Current 6-8A

Hyper Speed Brushless Outrunner CDROM Motor

CAN BE MOUNTED ON STICK WITH OPTIONAL STICK MOUNT

This is a high speed motor.

OUTSTANDING performance for small wings

KV	2500
Weight	23g
Price	$ 20

Torque Power Brushless Outrunner Motor

CAN BE MOUNTED ON STICK WITH OPTIONAL STICK MOUNT

Powerful motor great for most RC planes up to 35oz and 3D planes up to 16 oz

KV	1050
Weight	54g
Price	$ 19

Input Voltage : 7.4V~14.8V (2~4S Li-po)
Kv : 1050 rpm/V
Max. efficiency current : 5~12A
No load current : 0.42A@7V / 0.55A@10V
Internal Resistance : 0.16Ohm
Stator Dimensions : 23mm X 10mm / 0.90in X 0.39in
Shaft diameter : 3mm / 0.11in
Weight : 54g / 1.90oz
Number of poles/magnets : 12

C23-L 1050 Voltage Current Thrust RPM Thrust Input Eff. g/watt Eff. oz/watt

EP7035 7.00v 1.50A 104g 6900 rpm 3.64oz 10.50W 9.90g/W 0.346 oz/watt

EP7035 10.00v 2.60A 200g 9515 rpm 6.99oz 26.00W 7.69g/W 0.269 oz/watt

EP8040 7.00v 2.80A 204g 6465 rpm 7.13oz 19.60W 10.41g/W 0.364 oz/watt

EP8040 10.00v 5.10A 400g 8745 rpm 13.99oz 51.00W 7.84g/W 0.274 oz/watt

EP8040 12.00v 6.60A 526g 10095 rpm 18.39oz 79.20W 6.64g/W 0.232 oz/watt

HD8060 7.00v 4.30A 234g 5985 rpm 8.18oz 30.10W 7.77g/W 0.272 oz/watt

HD8060 10.00v 7.60A 426g 7875 rpm 14.90oz 76.00W 5.61g/W 0.196 oz/watt

HD8060 12.00v 9.80A 532g 8955 rpm 18.60oz 117.60W 4.52g/W 0.158 oz/watt

EP9047 7.00v 5.60A 340g 5475 rpm 11.89oz 39.20W 8.67g/W 0.303 oz/watt

EP9047 10.00v 9.30A 570g 7155 rpm 19.93oz 93.00W 6.13g/W 0.214 oz/watt

EP9050 7.00v 5.00A 324g 5775 rpm 11.33oz 35.00W 9.26g/W 0.324 oz/watt

EP9050 10.00v 8.40A 552g 7515 rpm 19.30oz 84.00W 6.57g/W 0.230 oz/watt

EP9050 12.00v 10.50A 702g 8385 rpm 24.55oz 126.00W 5.57g/W 0.195 oz/watt

EP9070 7.00v 6.90A 332g 4965 rpm 11.61oz 48.30W 6.87g/W 0.240 oz/watt

EP9070 10.00v 12.00A 572g 6360 rpm 20.00oz 120.00W 4.77g/W 0.167 oz/watt

HD9075 7.00v 7.30A 312g 5055 rpm 10.91oz 51.10W 6.11g/W 0.213 oz/watt

HD9075 10.00v 11.50A 472g 6405 rpm 16.50oz 115.00W 4.10g/W 0.144 oz/watt

EP1047 7.00v 7.60A 430g 4875 rpm 15.03oz 53.20W 8.08g/W 0.283 oz/watt

EP1047 9.00v 10.30A 586g 5715 rpm 20.49oz 92.70W 6.32g/W 0.221 oz/watt

EP1060 7.00v 6.10A 378g 5295 rpm 13.22oz 42.70W 8.85g/W 0.310 oz/watt

EP1060 9.00v 8.90A 538g 6345 rpm 18.81oz 80.10W 6.72g/W 0.235 oz/watt

HD1080 7.00v 8.90A 354g 4515 rpm 12.38oz 62.30W 5.68g/W 0.199 oz/watt

Brushless Outrunner Motor 08 STAR

now available as stick mount only. same mount as 09

KV	1100
Weight	50grams / 1.76 oz
Price	$ 14

NEW IMPROVED DESIGN

ALUMINUM STICK MOUNT/HEATSINK INCLUDED

Brushless Outrunner Motor

Bm2410-08 Star Wind

2 prop nuts & 1 washer

3mm shaft diameter

Configuration:	Propeller:	Volts:	Amps:	Thrust:
Direct Drive	1047	7.4V	6.0A	12.3 oz / 344.4 grams
Direct Drive	1047	8.4V	7.3A	14.7 oz / 411.6 grams
Direct Drive	1047	9.6V	8.6A	17.6 oz / 492.8 grams
Direct Drive	1047	11.1V	10.9A	21.5 oz / 602 grams

Brushless Outrunner Motor 12 Star

GREAT UPGRADE MOTOR FOR GWS SLOW STICK

KV	970
Weight	56grams / 1.97 oz
Price	$ 14

NEW IMPROVED DESIGN

ALUMINUM STICK MOUNT/HEATSINK INCLUDED

Configuration:	Propeller:	Volts:	Amps:	Thrust:
Direct Drive	12 x 6	11.1V	7.8A	17.00 oz
Direct Drive	10 x 4.7	11.1V	6A	16.00 oz
Direct Drive	10 x 4.7	7.4V	3.5A	10.00 oz

Brushless Outrunner Motor

Bm2410-12 Star Wind

2 prop nuts & 1 washer

3mm shaft diameter

10mm x 10mm Aluminum stick mount

Brushless Outrunner Motor 21 Delta

21 DELTA COMES WITH GOLD FIREWALL MOUNT JUST LIKE THE 08 STAR IN PICTURE ABOVE

NO STICK MOUNT

KV	1750
Weight	49grams / 1.74 oz
Price	$ 14

NEW IMPROVED DESIGN

ALUMINUM STICK MOUNT/HEATSINK INCLUDED

Brushless Outrunner Motor

Bm2408-21 Delta Wind

Max Current 15A

Use 15A ESC with this motor

Suitable for 2-3 cell Lipo

Firewall mount capable

2 prop nuts & 1 washer

3mm shaft diameter

10mm x 10mm Aluminum stick mount

Configuration	Prop	Volts	Amps	Thrust
Direct Drive	8040	7.2V	8.2A	3342.86 grams / 12 oz
Direct Drive	8040	8.4V	8.6A	394.29 grams / 13.8 oz
Direct Drive	8040	9.6V	11.1A	485.71 grams/ 17 oz
Direct Drive	8040	11.1V	13.1A	600 grams/ 21oz

FEIGAO 12mm Brushless Motor 1208430S 120 series

Recommended 2mm bullet connectors are available in Connectors section

KV	5250
Weight	10.5g
Price	$ 32.99

Brushless Motor

Shaft size: 1.5mm

Size: 12 mm Diameter x 22mm Long

Good for LPS gearbox applications

and some 2S lipo and 1S lipo direct drive applications

Configuration:	Propeller:	Volts:	Amps:	Thrust:
LPS 6.2:1 Geared	EP-7060	7.4V	1.7A	4.0 oz / 114.29 grams
LPS 6.2:1 Geared	EP-8047	7.4V	1.9A	4.8 oz / 137.14 grams
LPS 6.2:1 Geared	EP-8060	7.4V	2.1A	4.9 oz / 140 grams

Feigao Outrunner CNC CDROM Brushless Motor 380YS19

1 left

OUTSTANDING MOTOR FOR A SMALL FOAM PARK FLYER

VERY POWERFUL

KV	1283
Weight	32g
Price	$ 40

Normal working Amps: 5A
Resistance:0. 3861
KV: 1283
IO(A):0. 6
Size: 28.5*20mm

GREAT MOTOR FOR SMALL BALSA OR FOAM MODELS

AROUND 20in WINGSPAN

WHAT WE USE IT IN:

BLUE FOAM CUB & BIRD DOG with 7x5 up to 8x6 prop on a 3S Lipo

Can also use 2S pack on 8x6 prop for slow flying

NEW 300XD Brushless Outrunner 3D Motor SPECIAL

PERFECT FOR SMALL 3D FOAMY UNDER 10oz

KV	1150
Weight	1.2oz / 33g
Price	$ 18

Max power output: 150W

Output shaft diameter: 3mm

MAX CURRENT: 7A

Configuration:	Propeller:	Volts:	RPM	Thrust:
Direct Drive	9x4.7APC	7.4V	6000	10oz / 283g
Direct Drive	9x4.7APC	11.1V	7400	17oz / 481g

SHAFT CAN BE PRESSED OUT TO RUN AS PUSHER OR PULLER. WHEN PRESSING THE SHAFT OUT TO THE ROTATING CAN SIDE IT IS NECESSARY TO INSTALL AN E-CLIP (MOON CLIP) ON THE OTHER SIDE.

THIS MOTOR WORKS GREAT WITH ALUMINUM STICK MOUNTS FROM COBRI OR OTHER SIMILAR MOUNTS.

YOU CAN ALSO USE GWS 400 (BLACK) GEAR BOX TO MOUNT THE MOTOR (WITHOUT THE GEARS OF COURSE)

ASK ABOUT OUR 4 POINT PRESSURE PROP ADAPTERS THEY LOOK GREAT WITH APC PROPS AND FIT THIS 3MM SHAFT PERFECT.

FEIGAO 300 Brushless 130S series 1 left

KV	3600
Shaft	2mm
Price	$ 30

GREAT REPLACEMENT FOR BRUSHED 300-380 SIZE MOTORS

20mm Motor - Short Can

Turns: 26 turn

Shaft Size: 2mm

KV Rating: 3600 (RPM per V)

Max Amps: 10

High quality bearings.

2 pole Neo rotors.

State of the art compressed winding technology.

WHAT WE RUN IT IN:

RC18T with 2S 2200mAh lipo for on-road racing

Fits stock RC18 mounts

REPLACES ANY GWS 300-380 Brushed motor