|
|
| Case: | 1x - Macintosh IIcx, slightly scratched and yellowed (I pulled the best parts from each of the three I had) |
| Main logic board: | 1x - Yosemite, Rev. 1 |
| Auxilliary logic boards: |
1x - Front control panel with aluminum shield 1x - Firewire module 1x - Belkin USB-to-PS/2 adapter board, minus housing 1x - Griffin Technology gPort |
| Memory: |
1x - 128MB Generic PC100 DIMM 1x - 256MB Generic PC133 DIMM 2x - 256MB Kingston ValueRAM PC133 DIMM |
| Audio: |
1x - G3 speaker with plastic housing |
| Video: | 1x - ATI Nexus 128, 32MB, PCI |
| UltraATA: | 1x - ACard ATA/133 (AEC-6280M) controller, PCI |
| SCSI: | 1x - Initio BlueNote, PCI |
| CD-RW: | 1x - Plextor 8/4/32x CD-RW, internal IDE |
| Hard Drive: | 1x - Seagate Barracuda IV 80GB, 7.2K RPM, UltraATA/100 |
| Floppy Drive: | 1x - Imation SuperDisk (rev.2) 1.44MB, auto-inject/auto-eject, internal, IDE |
| Brackets: |
1x - Plastic Apple Macintosh IIcx/ci drive carrier (highly modified) 1x - Metal 5-1/4" bay hard drive carrier (slightly modified) |
| Cables: |
1x - Rounded, custom-length IDE 80-conductor, 2-connector ribbon cable 1x - Custom-length IDE 80-conductor, 3-connector ribbon cable 1x - Standard 18" IDE 80-conductor, 3-connector ribbon cable 1x - USB A-to-B cable 1x - Custom-length ribbon cable for Griffin Technology gPort 2x - Custom removable disk eject button/cable 1x - Custom power on/sleep button/cable 4x - Custom LED cable with Blue T1-3/4 (5mm) LED |
| Power Supply: | 1x - PowerMan 300W (FSP300-60BT) ATX PSU, modified |
| Cooling: |
1x - Panaflo 80mm fan (from IIcx power supply) 1x - Alpha PAL6035 heat sink (modified) |
| Miscellaneous Hardware: |
3x - Apple Macintosh IIcx/ci LED light pipe (upper type) 1x - Apple Macintosh IIcx/ci LED light pipe (lower type) 2x - 3/4" square x 3" long aluminum angle stock 2x - 3/4" square custom length (less than 1") aluminum angle stock 1x - 5-1/2" x 11-7/8" x 3/4" Lucite sheet stock 2x - 1" x 3-7/8" x 3/4" Lucite sheet stock 1x - Spare ATX power supply retaining bracket (from Cooler Master case) 3x - miniature SPST, momentary contact switch 9x - 3/8" stand-off 9x - 6-32 rounded-Phillips-head machine screw An assortment of nuts, bolts, and washers A variety of adhesives (epoxy, cyanoacrylate, plastic solvent) and putty (Milliput super fine white epoxy putty) A volume of spray paint (Tamiya TS-24 purple, Tamiya TS-13 clear, Plastikote flat white primer) A smidgen of solder and flux. Several lengths of 24AWG wire A few snips of heatshrink tubing 4x - Standard 0.100" spacing PCB-mount 0.025" square post male header 5x - Standard 0.100" spacing single row, dual-socket connector housing 10x - Standard female crimp pin connector for 0.025" square post Several bits of wet-dry 340-, 400-, and 600-grit sandpaper A lot of patience. |